Manufactured from carbon steel, SilverTip sawmill blades can be used on both portable and industrial sawmills and is also suitable for horizontal resaws. Carbon is the most common steel used in narrow-band sawing and can be resharpened, but typically not as often as a blade made with high-alloy steel.
Typically not resharpened on horizontal resaws using narrow widths (1", 1.125")
Wood-Mizer Sawmill Blades
From green softwoods to abrasive hardwoods, Wood-Mizer manufactures an extensive range of sawmill blades with more than 100 combinations based on profile, width, thickness, tooth spacing, and alloy for any type of sawing or resawing application. Each Wood-Mizer sawmill blade tooth is precisely set by computer-controlled equipment and completely profile ground tip to tip using super abrasive CBN grinding technology to ensure the highest quality blade performance. Made in the USA, all Wood-Mizer blades are quality checked for performance throughout more than 100 tests and inspections from the selection of raw materials to the final grind. Count on Wood-Mizer sawmill and resaw bandsaw blades for unmatched quality, accuracy, and performance across the board.
A. Tooth Spacing is the distance between each tooth from one tip to another. Shorter tooth spacing (1/2", 5/8", 3/4", and 7/8") is generally used for low horsepower sawing (24HP or less), secondary processing, and resawing, while wider tooth spacing (1” and 1-1/4”) is ideal for high production, high horsepower (25HP or more) operations.
B. Gullet is the area between teeth that captures and removes sawdust while providing strength in the tooth. The tooth height must be tall enough to allow the gullet to carry out sawdust from the cut.
C. Tooth Height is the distance from the lowest point of the gullet to the highest tip of the tooth. Taller teeth (4°, 7°, and Turbo 7° hook angle) provide more performance in higher horsepower (25HP or more) with increased sawdust removal. Shorter teeth (9° and 10° hook angle) are better for lower horsepower (24HP or less), small log diameter sawing, resawing, and secondary processing.
D. Hook Angle is the number of degrees that the tooth face leans forward of 90 degrees. The hook angle should be chosen based on the type of wood you are sawing.
E. Tooth Set is the distance the tooth is bent beyond the body or raker tooth of the blade. Tooth set clears a path in the wood for the body of the blade which is measured by kerf or the total amount of wood removed by the blade with each pass. Wood-Mizer thin kerf blades remove less than 1/10” which produces about 20% more boards per log than circle mills or chainsaws.
F. Blade Width is the distance between the tip and base of the blade. Wider blades (1-1/2" to 2") are designed for higher horsepower (25HP or more) sawmills, provide a faster feed rate, and are able to be resharpened more. Narrow blades (1- 1/4" to 1-1/2") are for lower horsepower sawmills (24HP or less) and more difficult sawing.
G. Blade Thickness is the thickness of the blade. Thicker blades (.045", .050", .055") provide faster feed rates and better cutting performance in difficult sawing conditions such as knotty, frozen, dry or extremely hard material, but requires higher horsepower (25HP or more). Thinner blades (.035", .038", .042") provide longer flex life with lower horsepower sawmills (24HP or less) where production or speed is not a primary factor.
Compra sierras de 158" compatibles con:
Shop 158" sawmill bandsaw blades compatible with:
Most Affordable
Acero al Carbono SilverTip
Most Popular
Acero de Alta Aleación DoubleHard
Specialty
Acero en Doble BiMetal
Specialty
Acero de Carburo RazorTip
El espesor es el grosor del cuerpo de la sierra del aserradero sin incluir el diente.
La anchura es la distancia entre la punta y la base de la sierra del aserradero.
El ángulo de diente es el número de grados en que la cara del diente se inclina hacia adelante con respecto a los 90 grados.
El ángulo de lomo es el número de grados en que la parte posterior del diente se inclina hacia atrás con respecto a los 90 grados.
El ángulo de diente y el ángulo de lomo deben elegirse en función del tipo de madera que estás cortando y del tipo de equipo que se va a emplear.
El paso de la sierra es la distancia entre cada diente, de una punta a otra. El paso de la sierra también se utiliza en referencia al espaciado de los dientes, como el número de dientes por pulgada o DPP en una sierra de cinta.
Unmatched Performance
At the heart of every great sawmill and resaw are the industry’s best sawmill blades. To ensure the ultimate sawmill blade performance across the board, Wood-Mizer designs and manufactures our own blades and is the only portable sawmill equipment manufacturer that does so.
Unmatched Selection
From sawing green softwoods to abrasive hardwoods, Wood-Mizer offers an extensive range of sawmill bandsaw blades with more than 100 combinations based on profile, width, thickness, tooth spacing, and material for any type of sawing or resawing application.
Unmatched Quality
Each Wood-Mizer sawmill blade tooth is precisely set by computer-controlled equipment and completely profile ground tip to tip using super abrasive CBN grinding technology. From the selection of raw steel to performing more than 100 tests and inspections through the final grind, we are dedicated to providing the highest quality sawmill blades on the market.
Unmatched Compatibility
Wood-Mizer gives you more choices by manufacturing sawmill blades for Wood-Mizer, Baker, Cooks, Hud-Son, Norwood, Timberking, Timbery, Woodland Mills, and more band sawmills and resaws!
